Home > Hp Laserjet > Hp Laserjet Ii P Error Message 52

Hp Laserjet Ii P Error Message 52

Plug the product directly into the wall socket. If message persists, verify with the cartridge manufacturer the installed cartridge was designed for use with that model printer. Check that the rear cover is closed; an open rear cover may cause a paper jam. Replace fuser. 2. http://train2solution.com/hp-laserjet/hp-laserjet-4000-error-41-3.html

Replace the environmental thermistor. 4. If the display remains blank, service is required. To prevent reoccurrence, reserve more memory for this environment area. For modular I/O (MIO) cards, this means there was an abnormal connection break.

Use with caution; always do a self-test before the cold reset to maintain a record of the printer's current settings. Turn the printer off, then on again. Clear message by pressing SHIFT and Continue on the printer. In December the printer would go through the initial diagnostic routine, but when the first print job came it would at first sound fine, but then make a longish whining noise

Message: 51 Error All HP LaserJet Printers 51 Error All - The printer was unable to detect the laser beam. Misadjusted or bent Switchback Assembly. IIISi/4Si Only: 1. Message: Config Lang HP LASERJET IIP, IIP+, IID, III, IIIP, IIID, and IIISi, 4, 4M, 4Plus, 4MPlus, 4P, 4MP Printers Config Lang HP LaserJet IIP, IIP+, IID, III, IIIP, IIID, and

To print the job as requested, install additional memory. Check Door Open sensor flag. The owners manual says that an error 52 is a scanner malfunction. Message: 12 Printer Open HP LASERJET II, IID, III, IIID, IIISI, 4, 4M, 4Plus, 4Mplus, 4Si, 4Si MX Printers 12 Printer Open HP LaserJet II, IID, III, IIID, IIISI, 4, 4M,

I don't have their numbers but you should be able to get them from the 800 directory. 800-555-1212 <

IIP, IIP+, IIIP Only: 1. is the most expensive part and on exchange you can get one for about $150-200. If the printer "sticks" on 05 Self-Test, turn the printer off and back on. This problem can be caused by software/drivers, memory PCA's, font macro personality cartridges, or optional I/O cards. 2.

Join our community for more solutions or to ask questions. news If the error persists contact your dealer or HP Service Technician. The HP LaserJet printer uses XON/XOFF and DTR/DSR signal protocols rather than ETX/ACK protocol. 2. The printer will still print, but will only be able to use the memory installed below the SIMM in question.

Measure the resistance between the fuser connectors. If the error persists, replace the main motor. If the message always appears when the printer is turned on, the printer will still operate, but it should be serviced to correct the problem. have a peek at these guys Message: W0 Job 600/A4, HP LASERJET 4, 4M, 4SI, 4P Printers W0 Job 600/A4 HP LaserJet 4, 4M, 4Si, 4P printers The job was printed at 600 dpi with page protection

Check entire paper path, check all sensors and flags. 13.21/13.33 Door open jam. 8000/8100 Only: 13.1 Paper late jam at PS2. 13.2 Paper delay jam at PS1 13.5 Fuser output, paper Clear message by pressing SHIFT and Continue on the printer. is between 0000J00000 and 2949J2222 2.

Message: 51 Error HP LaserJet 4V Printer 51 Error HP LaserJet, 4V Printer There is a problem with the fiber optic cable.

  • Reseat connectors J002 on the DC Controller and J601 on the LaserDrive PCA. 4.
  • Replace formatter PCA. 4000/4050/4100/5000/8000/8100 Only: 1.
  • If the error persists, consult service.
  • Turn the printer off and verify the optional interface card is installed correctly.
  • Gemini02 I work on behalf of HPClick the Thumbs Up below to say “Thanks” for helping!

HP Laserjet series 2 '50 SERVICE' code?? 8. View Solution. By default, the printer lowers the DTR polarity and sends XOFF (DC3) to suspend the flow of data. Message: 71 Error HP LASERJET II, IID, IIP, IIP Plus, IIID, IIIP, IIISi, 4Si, 4Si MX Printers 71 Error HP LaserJet II, IID, IIP, IIP Plus, IIID, IIIP printers Indicates an

might be something else. On the HP LaserJet IIP and IIIP Printers, Unit 1 and Unit 2 refer to the top and bottom slots respectively. If the error appears again, repair service is required. http://train2solution.com/hp-laserjet/hp-laserjet-1200-error-with-windows-7.html Replace DC controller.

Bad registration sensor or bad fuser exit sensor. Make sure fuser is correctly seated to AC Power PCA. 2. Then it became sort of uniform background of grey, but a little "streaky". Always turn off and unplug the printer when removing I/0 cards.

Message: 72 Service, LASERJET II, IID, IIP, IIP+, III, IIID, IIIP Printer 72 Service LaserJet II, IID, IIP, IIP+, III, IIID, IIIP printers A font cartridge was removed from the printer S.E.R. The printer door/lid is open. 2. Thanks again for your help.

I took the toner cartridge out and examined it and there was lots of toner on the drum, dry and dusty. Try the DIMM in another slot. (The firmware DIMM must remain in slot #4—the lowest DIMM slot.) 3. Check transfer guide assembly. 3. Temporary printer error, check printer's configuration. 57 ERROR II, IIID Only: 1. 57-1 Error - Incompatible memory card in front slot. 2. 57-2 Error - Incompatible memory card in rear slot.

If it spins up smoothly, then it is a laser PCA at fault. Message: 51 Error HP LaserJet 4Si, IIISi Printers 51 Error HP LaserJet, 4Si, IIISi Printers The toner cartridge is defective. If this error occurs, press the Continue key and the printer will repeat the page. Info on this problem is available at http://www.error52.html -- Jeff http://www.all-laser.com All Laser Service Laser

Check the optional duplexing paper path if the duplexer has been installed. Pull the sealing tape tab to remove the strip. 3. If the problem persists, contact the vendor from whom the card was purchased. Replace the laser/scanner. 5.

You need to take the unit to a service facility if you don't know what these parts are. It is a HP Laserjet Professional P1102 Solved!