Home > Hp Laserjet > HP LaserJet 4200 Issue

HP LaserJet 4200 Issue

Contents

Figure 40: Inserting fuser Install the rear output bin. If the above action does not solve the issue, contact HP or authorized service provider. Figure 45: Disconnecting cables Grasp the cover on the right side of the printer and pull it firmly toward the rear of the printer until it stops. top 13.10.00 FUSER JAM Description A paper jam exists in the fuser area. this content

Look for the jam in another location, contact HP, or contact an authorized service provider. by unknown on May 3, 2005 at 5:24pm Add comment Please sign in to comment 0 For the tray feeder problem - HP will replace the tray with a "new and An improper communications protocol might be in use. alternates with 68.X PERMANENT STORAGE FULL To continue press (Select) Description A nonvolatile storage device is full. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=84028

Hp Laserjet 4200 Error Codes

Some non-HP parallel cables might be missing pin connections or might otherwise not conform to the IEEE-1284 specification. Turn the printer power off. The outside plastic and metal frame look the same, but the inner wiring is different. PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support Account Login Shopping Cart My

If the toner gets on clothing, wipe it off with a dry cloth and wash the clothing in cold water. top 41.3 UNEXPECTED SIZE IN TRAY XX For help press ? top CLEARABLE WARNINGS and AUTO CONTINUE settings Some printer messages are affected by the printer CLEARABLE WARNINGS and AUTO CONTINUE settings. Hp Laserjet 4250n 49.4c02 Service Error The JOB setting determines that the clearable warning message appears until the end of the job that generated the message.

Every time I place more than say 20 sheets of paper in the tray, I place it in the printer I watch it rise up, but then instead of stoping it Hp Laserjet 4200 Not Printing If you run into this issue print a config page. X Description 0- Scanner error 1- Scanner startup error 2- Scanner rotation error Action Press the (Select) button to continue. http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=84030 Reload the paper and close the tray.

Action NOTE: Press the ? (help) button for detailed information about clearing the jam. Hp Laserjet 4200 Manual Whenever the printer is ready, not busy, and has no pending warning messages, the status message “Ready” is displayed if the printer is online. Open the top cover and remove the print cartridge. Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps.

Hp Laserjet 4200 Not Printing

Action Turn the printer off and then on. Figure 62: Print cartridge Close the top cover. Hp Laserjet 4200 Error Codes If it was it would not work even with 20 sheets. Hp Laserjet 4200 Network Setup Open the rear output bin and remove.

Figure 9: Removing the jammed paper Make sure that the paper is flat in the tray at all four corners and below the maximum-height indicators. news Reach us at (608) 268-7600. alternates with 52.XY PRINTER ERROR To continue turn off then on Description A temporary printer error has occurred. Figure 22: Closing the rear door Remove the print cartridge and check for paper, remove all found and then reinstall the cartridge. Hp Laserjet 4200 Printing Problems

  • Figure 50: Pressing DIMM strait into slot Close the DIMM-access door.
  • Bend and then pull the sealing tab from the end of the print cartridge to remove the entire length of the tape.
  • Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps.

If the sealing tab cannot be removed, insert a new print cartridge and return the faulty print cartridge to receive a replacement. Figure 54: Removing the tray Pinch the release that is located on the left guide and slide the side guides to the correct paper size. As long as I don't place a large some of paper in the tray it seems to work fine, though I would like to fix this problem. http://train2solution.com/hp-laserjet/hp-laserjet-4350n-issue.html Please wait while we process your request.

Learn more » Printer Tech Support Every LPT Tech Support provider has worked in printer service since the early 1990s. Hp Laserjet 4200 Driver Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers Unfortunately, these cards had a board issue.

Action Remove any jammed media from the paper path.

top 21 PAGE TOO COMPLEX Description The data (dense text, rules, raster or vector graphics) sent to the printer was too complex. Action Turn the printer power off and then turn the printer power on. It is easy to move it back to its proper position. Hp 4200 Printer Figure 18: Replacing the entrance cover and closing Tray 1 Reinstall the print cartridge and close the top cover.

top 13.98.00 OPEN INPUT TRAYS THEN OPEN AND CLOSE TOP COVER Description The rear output bin was opened when the printer was attempting to send a page to the duplexer, a If possible, try to use a fresh ream of paper and do not fan the paper. When you put in more paper the motor can not handle the weight and this is why you get the error. check my blog Replace any defective print cartridge.

Action Press (Select) to continue.