Home > Hard Drive > How To Setup A Hdd As A Secondary Slave ?

How To Setup A Hdd As A Secondary Slave ?

Contents

by Greatfuldead101 / September 3, 2004 1:29 AM PDT In reply to: Re: Install old hard drive as slave drive? If installing two drives on the same EIDE (PATA) interface cable: Jumper the bootable drive as Master, and the other drive as Slave; then connect the Master drive to the black For more information, including step-by-step instructions, see: Install an extra hard disk in your PC and How to install an SSD in your PC Tags: PC Upgrades Share this article Share I've done this a couple of times on my and my kids' computers, and never had a problem. his comment is here

djaliplumeJul 19, 2011, 1:02 AM Hi. Install the SATA drive into an available bay in the cage. Using Write Signature & Upgrade Wizard: Click Next on the first screen, and then select the drive you wish to install (in this case Disk 1). You?

How To Slave A Sata Hard Drive

Your SATA connectors should be labeled one through however many you have. You may assign a drive letter that is not in use by other devices if you wish, then left-click on Next to continue. Anything that you store on a secondary hard drive remains unaffected in the event that your primary Windows drive becomes unbootable or fails.

At minimum, make sure you put the drive on IDE 2. Flag Permalink This was helpful (0) Collapse - Re: Thanks, Berfert by Berfert / August 27, 2004 4:08 AM PDT In reply to: Thanks, Berfert I notice that in another post About the rest I am not sure; too much depends on the specific drive model. How To Install A Second Sata Hard Drive In Windows 7 It all depends on how important the information is that's on the drive.

Once reported, our moderators will be notified and the post will be reviewed. What Is A Slave Hard Drive Select any available drive letter from the pull-down menu and click "Next." 15. Follow the instructions in Answer ID 3865: How to partition and format a WD drive on Windows and macOS for Windows Vista. http://www.wikihow.com/Configure-Master-and-Slave-in-BIOS-for-Two-Hard-Drive-Disk-in-a-Single-System Warnings Make sure you and your computer are grounded properly to prevent accidental electrical shock or Mother Board damages caused from electrical surges.

Laadimine ... Sata Hard Drive Slave Jumper Setting Your BIOS may have more settings than Cylinders, Heads, and Sectors; if so, simply enter 0 for them. Press the "Enter" key to detect and configure the primary hard disk, making it the Master Drive. 5 Move the cursor to the "Primary Slave" selection and press "Enter" again. If you do that, make sure you have all your driver disks for your Video, sound and what ever else is in there.

What Is A Slave Hard Drive

Terms of Use Privacy Policy Licensing Advertise International Editions: US / UK India CNET Reviews Best Products Appliances Audio Cameras Cars Networking Desktops Drones Headphones Laptops Phones Printers Software Smart Home useful reference Yes No Can you tell us more? How To Slave A Sata Hard Drive Select your primary (C:) partition and press ENTER on your keyboard to begin installing Windows XP. Master Slave Hard Drive Setup I will try that and let you know.

During the installation process, you will be given the option to create partitions. http://train2solution.com/hard-drive/how-to-install-old-hdd-as-slave-in-newer-pc.html Jeremy Blum 199 210 kuvamist 10:01 Install a Second IDE Hard Drive - Kestus: 9:41. Please note that we do not support our Solid State drives (SSD) on this operating system. Anyone out there know how good Garbage Collection is on the Corsairs?Did you notice it getting worse over time? Master Slave Hard Drive Jumper Settings

If you want multiple partitions on this hard drive see the additional instructions below: Adding Multiple Partitions to your Boot Drive durring a Windows Vista Installation: Important: Western Digital Technical Support I suppose there are even used hard drives available that have been replaced. That's where the grey cables from the harddrives plug into the motherboard. weblink if I get another, I'll just cycle the old one out.

Check the "Perform a quick format" box, then click "Next" and "Finish." Things Needed SATA data cable References (4) PC World: Instructions on How to Install SATA Hard DrivesChengdu Yiwo Tech How To Connect Two Sata Hard Disk In One Pc Photodisc/Photodisc/Getty Images Related Articles [Attach Multiple SATA Hard] | How to Attach Multiple SATA Hard Drives [Maxtor Hard Drive] | How to Slave a Maxtor Hard Drive [SATA Hard Drive] | Sobimatust sisust teatamiseks logige sisse.

Make sure the drive connectors face outward. 5.

pics, videos, dowloaded software and updates and the like). I would personally recommending using your extra drive to store the same as I do if you need to. hak1985org 93 480 kuvamist 15:13 Введение в BIOS - Kestus: 15:11. Обзоры гаджетов от ArtomU 219 503 kuvamist 15:11 Como jampear HD's IDE - Kestus: 15:10. Sata Master Slave If you wanted to attach two hard disks to the same channel, one had to be set to be the master, the other the slave.

She earned a B.A. The default value reflects the entire disk size. Start Windows Vista and allow the Operating System to boot to the desktop. http://train2solution.com/hard-drive/how-do-you-reconnect-old-drive-as-slave.html Also would help to know what model your corsair SSD is ( that will indicate the controller) and if it is a SATA II or SATA III.Also:The MB (make and Model).

It makes sense to me to "recycle" any usable components that still are good, as long as the computer case has room for the extra drive. So when I got a new drive and updated software, I left my "old" drive as "C" and installed the larger drive on D & E (partitioned).Occasionally, malware gets in (family I want to know how to make my old hard drive as slave and my new hard drive as master. MESSAGES LOG IN Log in Facebook Google Email No account yet?

For additional information on this limitation, please contact Microsoft Knowledge Base Article 184006. Select custom Install.That should take you to the page asking where to install. That means no jumpers to set and no fear of getting it wrong. Create an account EXPLORE Community DashboardRandom ArticleAbout UsCategoriesRecent Changes HELP US Write an ArticleRequest a New ArticleAnswer a RequestMore Ideas...

This information is provided as a convience to our customer - for technical assistance installing an OS, you will need to contact either your system manufactuer or the publisher of your I have 16gb of ram. Before installing XP I quick formatted the SSD in Win7 (by first installing another Win7 on the wd drive). If you need assistance with your drive you will need to connect the drive to a computer running a supported operating system prior to calling or emailing our support team.