Home > Hard Drive > How To Do A Slave Drive

How To Do A Slave Drive

Contents

It's wise to check your motherboard manual and connect a new drive to a matching SATA port (one running at the same speed as your drive). grandpaw Flag Permalink This was helpful (0) Collapse - Re: addendum by ITVern / September 2, 2004 8:47 PM PDT In reply to: addendum You could install the old HD in Kees, I don't understand your comment, "Today's machines derail people as they set the drive to SLAVE and new spiffy machines actually need the drive set to CABLE SELECT and then Previous PostHow To Install A New Hard Drive To Replace An Old OneNext Post3 DIY Computer Repairs You Can Easily Do Yourself 10 comments Write a Comment Chris Balfoort August 31, http://train2solution.com/hard-drive/how-do-you-reconnect-old-drive-as-slave.html

I have secondary machine that it running win 98… I'm working on getting drivers for my WD 250 gig EXHD. No question is too small or big, simple or complicated, dumb or smart--what you'll find is a comfortable and friendly destination for you to discuss and get tips on fixing problems Find the diagram or instructions for your new drive on to set the jumper for the master/slave. No more flat ribbon cable from the mother board to the various drives. recommended you read

How To Slave A Sata Hard Drive

As for additional storage, it's okay too, just don't keep critical files stored soley on the old drive. Once you have removed the hard drive follow the instruction in our: How To Slave A Laptop Hard Drive Using USB Enclosure Video nigel halling October 3, 2008 7:12 pm Reply You can then get your files off or run data recovery software on the old drive to get your data back. DTI Data Recovery September 9, 2008 12:51 pm Reply # Kelly, It is possible that you have a virus, but it is more likely that there is either a problem with

  1. is there a way to slave it to a laptop that runs win xp pro?
  2. My OS was Windows XP 64 bit Pro; I have a lot of song files and such on there that I'd rather not lose.
  3. Please advise.

by KenR / September 3, 2004 12:14 AM PDT In reply to: Install old hard drive as slave drive? Flag Permalink This was helpful (0) Collapse - Re: Install old hard drive as slave drive? As with the majority of us, I need to get 6 years of pics out of hard drive (no back-up) I had a Gateway Windows XP-Home and it was hard booted How To Install A Second Hard Drive Windows 10 so someone told me to come here so i could do this hard drive slaving thing.

But remember, that programs from that old hard disk probably won't run, because they will have to be installed into the new Windows again. I saw this question above but didn't see the answer - My Western Digital 2500 (mine is a WD Caviar SE 1600 SATA from a Gateway) doesn’t have an obvious slave Jacqui Best August 18, 2008 5:09 pm Reply # Texas: You can connect the hard drive with a sata conrtoller internal to the machine if you like OR (and this is

I have successfully hooked up a different hard drive to this machine, but my maxtor drive didn't work.

DTI Data Recovery September 17, 2008 10:09 am Reply # Jay, HardDriveWorries, Both of you seem to be in a similar situation. How To Install A Second Hard Drive Windows 7 Good deal. It all depends on how important the information is that's on the drive. This is easy on most motherboards.

What Is A Slave Hard Drive

SUPER MEGA HELPFUL!!! http://www.wikihow.com/Configure-Master-and-Slave-in-BIOS-for-Two-Hard-Drive-Disk-in-a-Single-System grandpaw Flag Permalink This was helpful (0) Collapse - Re: Install old hard drive as slave drive? How To Slave A Sata Hard Drive Watch carefully for the initial boot screen to display and tap the necessary key to over-ride the boot process. How To Install A Second Sata Hard Drive mark June 18, 2008 7:55 pm Reply # I have a Maxtor one touch mini (120 GB).

I took my laptop to my I.T. his comment is here Also make sure that you did not insert the cable upside down. Inicia sesión para que tengamos en cuenta tu opinión. Thanks for voting! Master Slave Hard Drive Setup

I hate asking a question in this box but does Windows Vista (On a del computer) and the computer I want to use to slave it is using Windows XP Home i'll read the post while i wait for jacqui's reply. What can I do? this contact form Thank you!

When going to "my computer" it shows that it is there. Master Slave Hard Drive Jumper Settings After installing the additional hard-drive, you will need to change your computer's Basic Input Output System (BIOS) settings to "Master/Slave." Steps 1 Restart your computer. However, as some readers pointed out, the process of adding an IDE drive is significantly more difficult than a SATA drive, so in the interests of completeness and for those of

DTI Data Recovery July 23, 2008 10:09 am Reply # James, Like you said in your comment, the bad news is the drive isn't being recognised.

Here is a link to a video tutorial on how to slave a laptop drive to a USB enclosure. Do I really need that or can I just move the files that I see to various places to save off of this disk before I reload my OS to it? We often do work for the government and military where security is of prime concern. How To Connect Two Sata Hard Disk In One Pc and then all of a sudden it wouldnt even turn on.

Home About wikiHow Jobs Terms of Use RSS Site map Log In Mobile view All text shared under a Creative Commons License. is a disk usb 2.5″ with 120gb. Can anyone help me?? navigate here what is the couse of this problem, can you help me please?

For example, a modern SSD is likely to support the SATA III standard, also known as SATA 6.0Gb/s. DTI Data Recovery July 2, 2008 8:41 am Reply # jhazeph, Yes you can, in fact later today I am posting a video on how to slave a laptop hard drive alan July 16, 2008 9:58 pm Reply # Hi folks..